Hanging drywall is a relatively straightforward project, even for do-it-yourselfers. And
because it is an interim step in the overall process of finishing a wall, any mistakes that do occur can still be covered up. But the final task of finishing drywall can easily frustrate even very skilled do-it-yourselfers. Finishing is the very last stage, and this means that you have no more opportunities to fix flaws. This is it. You need to get it right.
Drywall finishing requires a good deal of craftsmanship, which is why the gypsum wallboard industry and drywall professionals have codified a set of professional standards that breaks
the process of finishing drywall into five distinct levels. Serious do-it-yourselfers should take note of finishing levels if they want their finish to look as professional as possible.
Drywall Finishing Levels
Level 0: Level 0 implies that no finishing of any type has been done. At this level, drywall is simply fastened to the walls or ceiling.
Level 1: This level means that drywall joint tape has been embedded in joint compound, but nothing further has been done.
Level 2: This next level means that you have skimmed a thin coat of joint compound over the tape and covered the drywall screw holes. You can stop at this level if you intend to cover the wall surface with tile, or if it's in a garage intended to be used for storage or a workshop-type space.
Level 3: At this stage, finishers apply a coat of joint compound to the tape and screws. Walls that will receive a heavy texture, such as knockdown texture, can end at this level. It would be pointless to progress beyond this level since texturing will produce a finish that is rougher than level 3.
Level 4: This is the classic drywall finish. Here, you apply another coat of joint compound to the tape and screws and sand the dried compound. This is the level that typically is used when a wall surface will be painted or covered with wallpaper.
Level 5: This highest possible level of drywall finishing involves applying a skim coat, if applicable.
There are three ways to apply a skim coat:
Use a roller: Thinned joint compound is rolled onto the wall with a thick-nap roller. Excess is scraped off immediately.
Use a taping knife: A series of six or eight dabs of mud are applied, each about 3 to 4 inches in diameter. Immediately, the mud is smoothed across the surface, then excess mud is scraped off.
Spray finish: Professionals have spray equipment to allow them to spray on drywall compound. This type of equipment can be rented at rental yards or even at some home improvement stores.
Where Drywall Finishing Levels Apply
In a perfect world, all drywall—every square inch of it—would be mudded and sanded
down to a mirror-smooth surface. While this is possible, it's not cost-effective. If you're hiring out the work, every step requires an additional visit from the drywall worker. For do-it-yourselfers, it's yet another day or two you add to the entire project. The nature of the space and how you use it may dictate the level of drywall finish that's appropriate:
Garages and workshops: A level 1 or 2 drywall finish may be completely sufficient in garages and workshops. Why mud and sand a space that is rarely ever seen? On the other hand, a car aficionado or an obsessive tinkerer might enjoy having a workspace that is as clean and smooth as any other wall found in the residential part of the home.
Wainscot-hidden wall surfaces: Are you putting in wainscoting? Then you don't have to put a premium finish on the lower 1/3 of your walls since it will get covered up anyway. A level-1 finish is fine for these areas.
Cabinet-hidden walls: Because kitchens are often blanketed with cabinets and appliances, much of the wall space doesn't need a level-5 finish.
Ceilings: Conversely, ceilings tend to get raked by natural light through the windows, highlighting pops, bumps, and depressions. For many homeowners, nothing less than a level 5 will do on their ceilings. At the very least, ceilings always call for a level-4 finish.
When Is a Level-5 Drywall Finish Needed?
A level-5 finish is a skim coat of joint compound (also known as mud) applied to a finish that you would normally leave at level 4. There are a few instances when you need a level 5 coating: when the finish will have glossy, enamel or non-textured flat paint; or when light is be angled low enough to highlight bumps and depressions. A level-5 finish is like icing on the cake. It's a premium finish that you will not get by default; you absolutely will need to discuss this with your contractor or drywall installer, as it is not normally considered part of the finishing process. Drywall finishing levels, in numeric terms, are not a normal part of the conversation between homeowners and contractors. Instead, you might discuss the final look or effect that you're aiming for. You might indicate that you want the dining room walls to be as smooth and flawless as possible or that the garage can have largely unfinished walls. It'll be up to the contractor to translate your requests to the drywall technician.
Why Precision Paintworks?
At Precision Paintworks, we take pride in our commitment to excellence and attention to detail. Our team of skilled professionals understands the importance of drywall finishing in achieving a flawless paint job. We offer a range of services tailored to your specific needs, ensuring that your space looks its absolute best.
Contact Us for Precision Painting:
Email: contactprecisionpaintworks@gmail.com
Phone: 240-406-8440
Website: Precision Paintworks
Whether you're embarking on a home renovation project or giving your office a fresh look, Precision Paintworks has the expertise and dedication to deliver exceptional results. Reach out to us today, and let's transform your space into a work of art.
Thank you for considering Precision Paintworks for your painting needs. We look forward to helping you achieve a flawless finish that will leave a lasting impression.
Comments